Parts & Accessories
Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed. - 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration - Chromed steel bearings - Wide bearing stance and axle design reduces flex and adds durability - Low drag main seal prevents contamination and reduces resistance - Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components
Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.
$11.25 - $24.99
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
Stan's Threaded Valve Extenders let you convert deep-section rims to tubeless. They're precision-machined from aluminum and are designed to fit deep-dish carbon and aluminum rims. And, they're threaded on the outside so you can install the Presta lock-ring nut for a perfect seal.
$16.00 - $17.99
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
Need a Shift Cable Fixing Bolt Unit for your Alfine S7000/S700 hub? Here it is. Now, get that bike back on the road!
- Replacement rear wheel skewer. - Specifically designed for use with Saris trainers. - Can be used for both indoor and outdoor rides.
Who knew we could make a thru axle disappear? The Maxle Stealth offers a light, low profile alternative to Maxle Lite. Features - 34g lighter than Maxle Lite - Easy installation with a 6mm Allen wrench
Yes! A 12mm thru-axle adapter for BOB Trailers. These Robert Axles for BOB Trailers are specifically engineered to attach the proven BOB Trailer to your thru-axle-equipped bike. Take full advantage of your modern bike with 12mm thru-axles and harness the rigidity of the thru-axle to haul your BOB Trailer. Set out on any adventure, big or small. Great for off-road tours, trail building, hauling cargo, and more! - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The axle ends are stainless steel which allows for mounting of the BOB Trailer bobbins. - No special tools required. The design allows for wheel installation or removal using your standard 5mm hex wrench. - Please note: This axle does not come with the BOB Trailer bobbins (those are available separately). Or, you can reuse your bobbins from the stock BOB Trailer Quick Release that came with your trailer. - Designed, built, and quality tested in the USA. Proven around the world.
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.
$53.99 - $54.00
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Lightweight and easy to install, there are Ritchey rim strips for all wheel sizes and types. - Easily snaps over your rims - Stretchy, tightly woven material provides a close fit and protects from abrasion - Sold as a pair - Not for tubeless set up
The Problem Solvers Axle Nut is perfect for wheels with solid axles (also called bolt-on axles). This quality nut is made of durable chrome-plated steel and features a built-in integrated rotating washer to hold tight.
On today's road forks, there are multiple front axle standards. Mavic front axle adapters allow you to mix and match without replacing wheels/forks. Most Mavic wheels can be fitted with specific adapters to match your fork end dimensions. - Converts Mavic road hubs to use 15mm axles - One pair required for each hub to be converted
Get rolling again with a replacement 10-speed freehub body for Mavic wheels.
Your riding doesn’t need to stop when the weather gets cold. Features - Giant road thru-axle trainer axle - Alloy construction - For use on 2017+ Giant road bikes with a 142x12mm rear thru-axle
Grade 10 chromium steel balls
$6.18 - $9.99
- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity
Replacement freehub spoke protector, in various sizes for different freehub sizes. - Made of clear plastic - 3 hooks for affixing to spokes
Secure - Prevents theft instead of standard 9 mm quick-release skewers Quick Assembly - Use proprietary key on frame dropout Construction - Stainless springs with chromoly axle
Aluminum Tubeless Presta Valve - MTB or Road
DT-Swiss Center Lock Adaptor. Allows 6-bolt rotors to be used on Center Lock hubs. - Rotor thickness between 1.8mm and 2.2mm - Easy assembly and only 29g - Made in Switzerland by DT Swiss - 230mm version accepts all rotors up to 203mm diameter - 160mm version accepts all rotors up to 160mm diameter
Make it more aerodynamic – this nipple is hidden inside the rim. DT Hidden Nipples are designed for high-profile rims, in which the inverted design is essential for optimum precision. They are very light and hidden on the inside of the rim: perfectly suited for high aero wheels. The nipples will align perfectly due to their spherical contact surface. - Weight: 22g for 64 nipples
Pro Head Reinforcement System (PHR) has a larger and more spherical contact area and is designed to balance loads transferred to the rim. The PHR system acts as a ball and socket interface, allowing the spoke to pivot into alignment while maintaining even, consistent contact during installation in order to follow the perfect trajectory from the hub to the rim.
The buyer's choice for wheel builders looking to save weight. ProLock nipples contain a special adhesive compound (by Loctite) which is activated when a spoke is threaded into the nipple, forming a durable bond. - 32 nipples weigh approximately 30 grams
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and to perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening
$21.90 - $34.25
Ease of use, lightweight, and optimum performance in a single product. The DT Pro Head shape, combined with both a torx and a square tool interface, makes wheel building a lot easier. The spherical contact surface aligns the nipple perfectly with the spoke. All-brass nipples are recommended for e-bike use. Weight: starting at 26g for 64 nipples.
$0.25 - $42.40
The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples
$23.10 - $35.00
DT Swiss tubeless-ready tape seals the rim for tubeless applications and also works well as rim tape for tube-type setups. - Durable adhesive tape works as a rim tape and airseal
$9.00 - $14.99
These rim valves are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Key features: - To be used exclusively with Bontrager Tubeless Ready (TLR) wheels - Required for Bontrager's Tubeless Ready (TLR) system setup - Removable valve core for easy sealant fill - Silver MTB valve is compatible with all Bontrager Mountain wheels except: Line XXX, Kovee XXX, and Line Pro 40 - Alloy Road Tubeless Rim Valve is compatible with all Bontrager alloy TLR road wheels